Thursday, October 22, 2015

DIY Barbie Doll House: Week #2 Cutting, Sanding, Priming


Welcome to the DIY Barbie Doll House. I've been a bit stalled on posting, but I have been working hard and will get two up this week, and two up next week. If you want to catch up, here's Week #1 DIY Barbie Doll House.

Everything was done, but I wasn't sitting down long enough last week to post.

Besides doing the scheduled Week #2 Cutting, Sanding, Priming there was still more planning and finally deciding on the appropriate lighting as well as ferreting out moldings, colors and fabrics. More on that later.

oldnewgreenredo

 After consulting the plans...we decided on a couple of adjustments and made the doorways and stairways 1/2"-1" wider than originally planned within the 48" width of the house.

I measured out the windows, doorways, and stair holes on the pre-cut 1/2"plywood pieces. Hubby cut the large pieces on the table saw and the holes with a saber saw.

There are twelve pieces in this house: 2 roofs, 3 floors with holes for stairways, 2 side walls with window cutouts,  1 garage wall, 1 bathroom wall on bottom floor, 1 kitchen wall on the stairway (open in a triangle) to  stairway to third floor, 1 bedroom/bathroom wall on the third floor 
and 1 back piece with the roof pitch.

We did not make any exterior doorways, (imagine them on the open side of the house)

oldnewgreenredo


On the bottom is the east wall of Ken's Bathroom on the stack of 16" wide sidewalls, floors and roof pieces. All surfaces were sanded with 60-grit sandpaper with an orbital sander. It has a dust bag attachment that basically doesn't work, so I did all the sanding outside.

oldnewgreenredo

This is one of the roof pieces, which we have left the full 48" and will cut after we see it assembled.


oldnewgreenredo
 After sanding it was clear the 'bad' sides of the plywood had a few knots and dark spots. Not willing to fight dark marks seeping through my primer and paint, I gave all dark spots and knots a good brushing of shellac. It dries quickly and seals up many imperfections.

oldnewgreenredo

I use sponge brushes for almost everything but detail work. They do not last long with shellac.
Since I had 12 pieces to deal with and 24 surfaces, I spread out on 3 sets of saw horses. The weather was warm, with low humidity, so everything dried very fast.

Next step was to fill all holes, dents, scrapes and knotholes. I used a new purple version of Elmer's wood filler that dried between white...with little shrinkage.After doing 24 surfaces...the first ones were already dry.

oldnewgreenredo

I rolled a latex primer on all surfaces very quickly because the weather started to look like rain...!

oldnewgreenredo

The dollhouse pieces all dried fast. Now the hard part is trying to picture new colors in the new Barbie house. One reason we are doing this, is the abominable purple and magenta pink PLASTIC for Barbie. So we are hoping to make the house a home, with more realistic colors and furnishings. Not that there won't be SOME pink.


oldnewgreenredo

Here are the middle walls for between the rooms with their doorways. It is a puzzle. Most of the materials used from now on except moldings will be recycled or vintage.

Now choosing, pink multi for the bedroom and bathroom, green & white for the kitchen, and white, green, teal for the living/dining room, and sand/beige/wood for the first floor Ken's Man Cave and bathroom + Chicago sports colors. Having had boys, I almost think I'm looking forward to the 'mancave' more than anything.

Ken's says so too, he's really tired of sitting in a pink and white bathtub and is looking forward to his
own shower in sand beige.

oldnewgreenredo

Coming soon, DIY Barbie House: Week #3 Windows and Surfaces--COLOR!



All the opinions and photographs in this blog are my own, I have not been paid or reimbursed in anyway for my opinions or posts. Please do not use my photos without linking back to this blog without my permission. 
Thank you for your cooperation, Sandi Magle 

And always, thanks for stopping by, 

Sharing at these parties: 
What's It Wednesday 
Share Your Cup Thursday
Vintage Charm 
Simple & Sweet Fridays
friday-features-linky-party-
Think and Make Thursday 
Funtastic Friday 
Shabbilicious Friday 
Feathered Nest Friday 
Best of the Weekend 
Silver Pennies Sundays 
That DIY Party 
Party in Your PJ's 
 Merry Monday Link Party
Metamorphisis Monday 



Sandi


Thursday, October 15, 2015

Vintage REDO: Making Tiered CookieTrays for Gifts


The Gifting Holidays are just around the Corner

 

I hate to say it, but with the cool breath of FROST in the air for the next three nights, 
and local merchants---pushing the orange/black to the side for red/green/glitz;
the *WINTER HOLIDAYS* are right around the corner. 

LAST YEAR, I thought ahead for a change after admiring some NEW Tiered-Cookie-Trays
 at a craft show...just like this---for $35.00 and up, I knew I needed quite a few, 
and the budget...well UGH!

oldnewgreenredo


During the OLD 1950's when I grew up...yes, I'm that OLD--
every house you visited had a gorgeous tiered-cookietray
 filled with nummy holiday baking and candies.  
I LOVE that Vintage tiered-cookietrays have made a comeback along with pedestal cakeplates.
I thought golly, I have a stash of OLD dishes here and there...
I could easily add to and REDO my own for my GIFT LIST.

oldnewgreenredo

Here is a great example of OLD plates that could easily be put together into a REDO tiered tray. 
I actually bought these at thrfit shops and Goodwill 
for as little as 25 cents each and up to $1.99 for the Castle plate. 
Keep in mind thick plates take longer to drill through---I mean way longer.
But all you need is elbow grease, a power drill, the handle hardware, drill bits and patience.

oldnewgreenredo


I  knew I needed seven sets for gifts, and I wasn't shy about spreading plates out 
on a ping-pong table at the store (Goodwill) to see what went together with my own.
Here I chose a pinecone theme for my sister-in-law with the beautiful house in the woods. 

Make sure you have a few extras in solids just in case of any breakage.
 (We had two plates not usable out of 32 after drilling)
oldnewgreenredo


 Here is a Cardinal themed set-up with the hardware, for a lover of cardinals. 
I chose a smaller red plate to include with the cardinal setup, so the cardianl tray can be used all year round. The best part they can be dismantled to store flat...just three plates and the hardware.


oldnewgreenredo
I chose NEW traditional hardware...by the dozen, but they come in many styles and finishes.
This hardware ran about $15.00 for 12 sets plus shipping.
It was a bit on the thin side, so next time I will order the thicker sets. 
Watch carefully where the shipper is located, as many are from China
 and shipping from there takes forever. Mine came from San Francisco.

All the pieces have plastic gaskets to protect the plates, 
 and easily fit together adapting to thick or thin plates. 
I only had one plate that was really too thick for the hardware. 

You will need a ceramic drill in the size to match the screws in your hardware.
The bit should be labeled for glass and tile, and plan on buying more than one.
We went through 4-5 bits for thirty-two holes....of different thicknesses. 
Drill from the top surface down...because if there is splintering, it will occur on the bottom then.
After drilling I sealed the holes with non-toxic (GREEN) acrylic sealer. 
I recommended handwashing for all the pieces on the tags I included with each tray.

oldnewgreenredo


This was an ivy green plate on the bottom with a solid top plate
 and a great vintage dessert plate with fruit in the square shape as an alternate top plate. 
This one was actually my favorite.
Green was chosen  for a friend who serves homebaked cookies at work.  



IT LOOKS LIKE GIFT LAND HERE!





Here are five completed REDO sets and an unassembled Cardinal set.

 The REDO tiered trays were a big hit, and everyone seemed thrilled. 
I offered to drill any plate they would like to add their own dishes, 
but No Takers....everyone seemed happy just the way they were.

Not too late to get started, and thanks for stopping by.
I'll be sharing at these great link parties:

Sandi



Wednesday, October 7, 2015

DIY Barbie Doll House: Week #1 Planning



Well this is a little different from my usual posts. Grandbaby will be three on Saturday and I will have call her Grandgirl after that. So, since she so loves the little Marx metal dollhouse we have in the basement, we thought we would build a BARBIE DreamingHouse for her for Christmas.

Now we are building the house substantial to last forever, but for the furnishings, I have been collecting things since March. Many items will be altered or handmade. Once a Week I will do a Barbie Post to update you on the progress of this very big project.

Step:1 

Planning-After researching the internet and looking for all the scale 1:6 meaning 1" in real life is 6" in Barbieland, same for Bratz and Monster high. There are some fabulous ideas online...and many, many Barbie DIY's. We decided to adapt an idea based on one bookcase plan. Built from 1/2" plywood this will be a substantial piece of furniture. This is the site I used for FREE PLANS.

Step:2 

My Plans were drawn to scale on grid paper...1 square = 1" or 6" in Barbie scale.

BarbieDIY oldnewgreenredo
Here is the original plan we adapted ours from, originally 51 1/2" tall by 45" wide x 12 1/4" deep.
Since Barbie furniture is scaled large we opted to increase the depth to 16" and also to add stairways, so we added to the width to be 48" exterior and that makes it 47" wide inside the house.

Our total height will be 48" which is the size of a 1/2 sheet of plywood for the back.

BarbieDIYoldnewgreenredo

Since I have been collecting OLD and used furnishings, I drew the plans---with furniture I had in mind, and some I will still have to make (sink, stove, counters, desk, shelving, side tables, lighting, bed)

My drawing above is the second floor showing kitchen to the left, stairwells, and dining/living room to the right.

I drew plans for each wall, floor and interior wall. Then I placed outlines of furniture on all the plans...to see if I had enough room or needed more items. This kept me from buying too much. The spaces filled  up quickly, and keeping in mind a three year-old playing with it all.


BarbieDIYoldnewgreenredo


The middle above is the left side wall, all three floors: bottom/garage, 2nd/kitchen drawn in, 3rd tub and window placement in bathroom. To the right are the interior walls and stairwells. This is very tight and will be steep. I have no idea how I'm making the stairs, yet...the railings will be minimal and will involve acrylic sheets (we have scraps around from some other projects).

Step 3:

Laying out the furniture on the to scale plans.

BarbieDIYoldnewgreenredo

The Dune Buggy will be parked in the garage on the lower left. The left wall is shown here, with garage on right, the kitchen on level 2, and the bath on level three(left).

BarbieDIYoldnewgreenredo

Today I transferred my plans to the rough cut pieces. To double check placements from my drawings, I set up the furniture roughly according to the plans. I altered windows..etc. to accomodate visuals.
Barbie furniture is scaled so low---I will be adding height to just about everything, except the kitchen
appliances.

BarbieDIYoldnewgreenredo

 Ken barely fits in the tub for the upstairs bathroom, that's OK, he will have a shower in his bathroom on level 1.


BarbieDIYoldnewgreenredo

Here is a panel I took from the Barbie shopper/vending machine, which I found still full of shoes/accessories for $3.99 at Goodwill, but it didn't work and was abandoned. Anyway I took the back off and am using the filigree panels (REDO) as windows for the bathroom and Barbies' bedroom --how cool is that? The cabinet itself will be the closet in the bathroom.


BarbieDIYoldnewgreenredo
Back to Ken's bathroom.

Lower Level 1, on the far right wall. Ken's blue shower is on the bottom with the toilet, and then his closet/wardrobe. Marked on the board are two windows. A narrow partition or screen will be put between the toilet and the wardrobe to give Ken privacy, from his dressing room.

BarbieDIYoldnewgreenredo

Here is Ken and his interior wall dividing the 1st floor Mancave and his bathroom. The (Barbie) sink unit was dismantled from the shower unit and will be mounted to the wall. Some towel holders are  removed for painting silver. His bathroom/Mancave will be in blue, brown and beige tones.
BarbieDIYoldnewgreenredo


The two plastic doors will be used for a wall cabinet...that will have mirrors on the inside of the doors, maybe. Everything will be manly brown-beige-blue.

Seriously everything I found was hideous pink or purple and needs a REDO.


BarbieDIYoldnewgreenredo

Step 4: 

Adjusting the plans to work with the furniture.

Right wall--the second and third floor. In the middle (level 2) the short pink couch will be REDONE and raised 1". The window is marked to scale with the sofa.  To the left is a 12" bed of Barbie's on the third level, she will have a double-bed though, which I am making NEW with that length.


BarbieDIYoldnewgreenredo

On the otherside of the Level 1 interior wall, is Ken's soon to be desk bookcase. I'm just playing here to see the proportions. I found two of these case things for 1.99 each at Savers, a REDO--They were from bead kits. I'm using one as kitchen cupboards and one for Ken's desk...which will be custom built from scraps. Again...nice blue, tan, browns in this room and lots of Chicago BEARS accents.


BarbieDIYoldnewgreenredo

He really looks like he wants to work here...LOL. The rest of the ManCave will be shown later.

BarbieDIYoldnewgreenredo

 Here is a rough layout of the kitchen. Hmmm, it's going to be tight. The cartons in the back are where the stove and counters will go. The sink will go next to the pink dishwasher (99cents), The refrigerator I bought NEW...$8.99 at Walmart.

BarbieDIYoldnewgreenredo

Can you see the stove on the right there? And I'll raise the shelves up to the top of the dishwasher...maybe granite countertops...You never know. Still looking for a stove and sink...but am prepared to build them if necessary. Kitchen will be green and white with appliances in Stainless steel. I found brushed chrome stickum paper at OfficeMax for 99 cents a sheet.

BarbieDIYoldnewgreenredo

The Fridge was a good buy, and came with some accessories. I think the pink handles have to go silver though.

BarbieDIYoldnewgreenredo

I'm thinking I may make the table drop leaf (REDO). How often will Barbie have company more than Ken? And that will uncramp the kitchen, besides company can be served on the dining table in the next room.

BarbieDIYoldnewgreenredo

On to the second floor living room, dining area. Two couches cornered with a round skirted table and lamp. I will raise each of the couches an inch...honestly they are too low for the height of the dolls.
This area will be greens/grays/black and silver.  I'm thinking tailored skirts and a bit of cushions with bolsters and pillows in contemporary prints.


BarbieDIYoldnewgreenredo

Here is an inexpensive table and chair set (comes with dinnerware) that I ordered online...was under $17.00 with shipping. The chairs are flexible plastic, and I'm not sure about them...I will be supergluing the table though. I sure don't want to put it together again. It is sturdy, as long as nothing slips out of place, hence the glue.

BarbieDIYoldnewgreenredo

The scale of this room is looking good, things to add yet, TV...birdcage, coffeetable, bookcase, lamps, lighting. The room is long and skinny...but that all should work.


BarbieDIYoldnewgreenredo
I'm excited about the 3rd floor vaulted ceiling Bathroom/Bedroom. The wood piece on the right will become an upholstered headboard to the double Barbie bed. With fru-fru skirted tables on the sides with lamps, it will fill the far right of the room. This room will be pink and white, and another color.
I have yet to pick out fabrics.

The large dresser is deep 4" and pretty good size. Painted a solid white with some pink handles, maybe a silver front. It will hold much of Barbie's wardrobe. A mirror and her accessories will be on top. A chaise,  side chair and dressing table will finish off this room. 


BarbieDIYoldnewgreenredo
Here is the layout at the top of the stairs. Artwork and a clock will be on the high wall of the stairway almost at the peak of vaulted ceiling. The pink dresser will be in front of the railings and banister of the stairs. Again, think silver, and some pink here. Thinking crystal or pearl knobs here.

BarbieDIYoldnewgreenredo

This is the bathroom/dressing room. On the right of the sink will be a cutout door to the bedroom

BarbieDIYoldnewgreenredo

The sink will be on this wall with a wonderful mirror above it...can't you see it?
The wardrobe (REDO-busted vending machine)....will hold accessories and shoes and hanging clothes and the vending area in the middle will become shelves for towels etc.


BarbieDIYoldnewgreenredo
And here is Ken again in the tub...in front of a filigree window...use your imagination. At the foot of the tub will be a tiled planter to finish off the tub. Again, think silver knobs, but this room will be pinkish, but only as much as I can stand.

Step 5:

Make a list of items still needed and shop for moldings.

I hope you weren't bored with all the planning, but this saved a fortune doing it this way. To buy a Barbie House already furnished of this size, would be $300-400 dollars, maybe more. And we will be less than half of that, for sure. Planning does save money and creates a NON-putrid pink haven for Barbie and Ken to live in. Many Barbie houses are 8" deep...which is only enough for a narrow bed along the back.

When Grandbaby turns 10, she can change it all,  however she wants to. That will be fun to do it all over again. I hope I am around to help her.

NEXT POST: Priming, Painting, Windows, Doors, and Electrical.

Dollhouse posts here,

Thanks for Stopping by, I appreciate all your comments and questions.
I will be sharing at these Parties:
Sandi

All the opinions and photographs in this blog are my own, I have not been paid or reimbursed in anyway for my opinions or posts. Please do not use my photos without linking back to this blog without my permission. 
Thank you for your cooperation, Sandi Magle

Last Week's Find: Cheese grinder to Fairies.



 Some Junkin', Thriftin', and Craft Show Finds


 Last week was very busy, but everytime I was out, I went to a thrift shop or garage sale, on the hunt for OLD, NEW, GREEN, to REDO.
Sunday, E and I went to a craft show...more on that later.

oldnewgreenredo

 You have already seen my Fall Fairy---she was hanging 
in a chandelier at a thrift store...
she is quite at home here.

oldnewgreenredo

Now here is my OLD ChiPPy-SHaBBy buy from last June. 
I didn't buy it at the Elkhorn Flea, but 
emailed Jeanine and paid her for it afterwards.
Saturday, I schlepped up to Wisconsin to pick it up. 
She had a lovely show in her garage, in the midst of cold temps, rain, and a fierce winds. 
The buying locusts had already descended...but you can see some of her show(s) Here.

oldnewgreenredo

 This will be going in my master bedroom redo...sometime this winter. I'm excited---it works, but I will be softening the green and yellow somehow...a REDO but can't wait.

oldnewgreenredo

 I bought this OLD cheese grater for my husband. The blades looked like it had been barely used.
The wood block fits tight...so I think it just sat on someone's shelf for a long time.
We will sand it down and use it. I will do some more
research on it.



oldnewgreenredo



 I think the green metal is so interesting...apparently a bit of 
manufacturing advertising also with the "V". 
The grater blades are actually two---one for each direction, 
this is for hard cheese or super fine shredding of vegetables.

oldnewgreenredo



 Here is the NEW second fairy---a bit of felted delight purchased at the craft show...adorable. 
I have ordered a matching gnome.
 I'm crafty but realize some things I will just not get around to making, and I purchase those.

oldnewgreenredo
My husband went to an Antique Mall without me...?????
and purchased these OLD small dollhouse furnishings for the 
1950's Marx Metal Dollhouse we have downstairs for Grandbaby to play with. 
The drawers all work on the little bed, mark on bottom says 1994, my gosh that's vintage now.
The stove is wood and I don't know if it will fit in as I do have some Remark furniture, otherwise it will end up in my Etsy shop.

oldnewgreenredo
 I found this gorgeous white throw----Twin size...rayon and cotton. It's perfect with minimal wear...and so textured and lovely. I'm tempted to make a coat of it as a REDO, but we will see.
Hubby bought the doll chairs set in a bag with the checkered chair and pink set below.



oldnewgreenredo

 It's really cute...a little garish...but then that dollhouse needs some color anyway.
One set will go on the patio.

oldnewgreenredo

Hubby again  found this table and chair set BARBIE sized... for the Barbie House (Xmas).
 It was 17.99 but I have seen the same for $45.00 on line +postage. 
This will be the largest purchase for the Barbie house
 as I have been collecting from thriftstores and garage sales since March.
PS...hubby is cutting the dollhouse out today, I have to get out there and photograph it.

oldnewgreenredo

And since we are talking about Christmas....
Smiley Snowman here, may become a smiley ghost for Halloween. 
Found him at the craft show. He is a REDO kettle lid...painted so sweet.
 And oh my gosh, ALL the holdiays are just around the corner.


THANKS for your stop by and I love hearing from you.


Sandi


All the opinions and photographs in this blog are my own, I have not been paid or reimbursed in anyway for my opinions or posts. Please do not use my photos without linking back to this blog without my permission. 
Thank you for your cooperation, Sandi Magle