Showing posts with label glue. Show all posts
Showing posts with label glue. Show all posts

Sunday, November 1, 2015

DIY Barbie Dollhouse: Week#4 Part 1-House Assembly and Moldings


Last week was a busy week with the NEW DIY Barbie Dollhouse. Chicagoland had cold weather and rain from the hurricane. We had intended to get to the lighting, but all the moldings and house assembly came first.

Choosing some composite moldings was an easy decision from Home Depot and Menard's and were perfect in scale and prefinished. They are fairly inexpensive for an 8-foot length, cut clean and easily.


oldnewgreenredo


Some fancy moldings were purchased at Michael's for the roof edge shown here with our hand made straight moldings we used for the window frames.

oldnewgreenredo

Tools we used, were simple and complicated: the square from my tool box, pencil, scissors for cutting the uneven edges of the composite trim, an exacto knife for cleaning up the edges. Composite molding edges clean up nicely with just a scrape from the knife.

oldnewgreenredo

Tools we used, were simple: the square from my tool box, pencil, scissors for cutting the uneven edges of the composite trim, an exacto knife for cleaning up the edges. Composite molding edges clean up nicely with just a scrape from the knife. The mini mitre-box on a wood surface and lots of clamps and PATIENCE.


oldnewgreenredo

My trusty little mitre box and my husband insisted on using glue, (Tite-Bond 3-Ultimate wood glue) which was messy and marked up all the prepainted walls and surfaces, but he is the construction foreman, so I just gritted my teeth and thought of all the touch-up I will have to do.

His wood glue is amazing though, and it holds pieces totally tight. Set-up time is 30 min, and he clamped my cut door moldings.



oldnewgreenredo

My creative second floor landing opening for the stairs proved to be more of a challenge. My husband showed me how to make the complicated angle cuts.


oldnewgreenredo

Here the clamps hold the moldings in place so the angle cuts can be marked.


oldnewgreenredo

After I made the cuts, the molding are glued and clamped. The green side goes to the kitchen side of the second floor.

oldnewgreenredo

Next Hubby installed the inside walls. These were screwed or nailed from below and from the outside walls. My husband and his clamps held the walls straight while the glue (more touch-up) dried.

oldnewgreenredo

I set a few pieces of furniture pieces which need to be flush against the walls, to work around for the floor moldings. I did the measurements and cut all the pieces and set them in. At this time, the entire kitchen will be molding free because of all the cabinets will be built in. Just like a real house.

oldnewgreenredo
The kitchen (green) will be filled with appliances and cabinets, no need for moldings along the walls.
oldnewgreenredo

The bathtub will be up against the wall, the trim placed along the corner walls.

oldnewgreenredo

Floor moldings on the second floor living room. More glue to cover up, LOL.

oldnewgreenredo

Here are the outside edges, showing the shape of the moldings. Whoops-- touch-up needed on the outside window trim.

oldnewgreenredo

 The molding on the second floor opening, with floor molding installed.



oldnewgreenredo

Hubby used shakes for the roof. He said it went quick and gives a nice look to the exterior. The scallop trim finishes off the front edge. He still needs to add pieces on the side.  Another trip to Michael's.

oldnewgreenredo

 You can see the screws holding the floors together, on the outside. This will be covered up with wood putty.

oldnewgreenredo

The shakes are large, but small ones looked so busy, we opted for the large shakes. Hubby glued the shakes and used a nail-gun. The roof cap is still under construction.

oldnewgreenredo

DIY Barbie Dollhouse so far. Now, what's next?


oldnewgreenredo

The stairs, at this point all the planning is out the window, we measure and build as we go. The risers are spotted through the floor. There are actually two being held together, you are seeing the stripes of the 1/2" plywood. Golly, I hope these work. Hubby has been delegated the stairs. More on next post.

oldnewgreenredo

I call this Fall Tablescape #2...LOL. With cookies for Halloween, all the tools and work going on in our kitchen.  Next week is supposed to be nicer weather, so the porch can be utilized. It's amazing I served dinner for 6 in the kitchen the next day with my regular Fall tablescape.



All the opinions and photographs in this blog are my own or I am in possesion of the originals, 
I have not been paid or reimbursed in anyway for my opinions, posts or products used. 
Please do not use my photos without linking back to this blog without my permission. 
Thank you for your cooperation, Sandi Magle

Thanks for stopping by and I will be sharing at these parties:
Sandi


Posted by at 19 comments:
Labels: , , , , , , , , , , ,
Subscribe to: Posts (Atom)